An environment that tests lubricants to the limit
The marine environment is one of the most aggressive for machinery and lubricants: salt water, constant humidity, temperature changes, vibration and, for many vessels, long periods of inactivity. In the marine sector, industrial lubricants must protect against corrosion, resist water washout and, in parts in contact with the sea, keep their environmental impact as low as possible.
Requirements vary greatly depending on the type of vessel. Large merchant ships have very large main engines and an engine room with dozens of different systems; work boats such as tugs, fishing vessels and harbour craft operate intensively in harsh conditions; pleasure craft alternate periods of use with long months laid up. The principle remains the same: each system must be lubricated with the product specified by the manufacturer.
Marine engines
The large slow-speed two-stroke engines of merchant ships have a particular feature: cylinder lubrication is separate from crankcase lubrication. A dedicated cylinder oil is injected directly into the liners, while a system oil lubricates the bearings and crankcase components. Cylinder oil contains an alkaline reserve, expressed as the base number, which neutralises the acids formed by burning the sulphur in the fuel: for this reason the product must be chosen according to the fuel in use.
Medium-speed four-stroke engines, used as main engines on many vessels and as on-board generators, instead use a single oil that lubricates both the cylinders and the crankcase. Smaller craft have inboard diesel and petrol engines, two- and four-stroke outboard engines and drivetrains such as sterndrives and reverse gears, each with its own dedicated oils.
On ships, system oil is kept clean with filters and centrifugal separators, which remove water and particles, and is checked periodically with on-board and laboratory analyses.
Water: the most frequent contaminant
In the marine environment, water can enter lubricants through condensation, seal leakage or washing. Oil contaminated with water loses lubricating ability, promotes corrosion and ages more quickly. Some signs are easy to recognise:
- milky or cloudy oil in sumps, gearboxes and sterndrives;
- water at the bottom of tanks or in samples left to settle;
- rust on dipsticks, caps and internal surfaces;
- grease washed out or emulsified in exposed joints.
In these cases the cause of the water ingress must be found and corrected before replacing the lubricant, otherwise the problem will come back.
Propeller shafts, propellers and thrusters
The propeller shaft passes through the hull inside a stern tube containing the bearings, which are lubricated by oil or by water depending on the design. In oil-lubricated systems, seals separate the lubricant from the seawater. Controllable pitch propellers, thrusters, stabiliser fins and other submerged equipment also contain oils which, if they leak, end up directly in the sea.
For these oil-to-sea interfaces, some areas require environmentally acceptable lubricants, meaning products that are biodegradable, of low toxicity and not bioaccumulative. The switch to these products should be planned with the equipment manufacturer, checking compatibility with seals and materials.
Deck machinery
Winches, windlasses, cranes, davits, hatches and wire ropes work outdoors, exposed to spray and rain. They require greases with high resistance to water washout and good anti-corrosion properties, hydraulic oils for the drives and specific wire rope lubricants able to penetrate between the wires and protect them from the inside. Cranes and lifting equipment also follow inspection programmes that include the condition of lubrication.
Pleasure craft: the seasonal lay-up
For pleasure craft, the most delicate period is often the time out of use. Before laying up it is good practice to follow the engine manufacturer's instructions, which usually call for the oil and filters to be changed: used oil contains combustion residues which, during a long lay-up, can promote internal corrosion. It is also worth checking the oil in transmissions and sterndrives, greasing the specified points and protecting exposed metal parts.
Safety and protection of the marine environment
Engine room and bilge water
In the engine room, oil leaks onto hot surfaces are a cause of fire: they must be eliminated and cleaned up immediately, and oily rags must be collected in closed metal containers. Oily bilge water must never be discharged into the sea except in the ways permitted by the international rules on pollution prevention; used oils and filters must be handed over to authorised port reception facilities.