Terms from A to C
A glossary for people who work with industrial lubricants: short, practical definitions of the terms found in data sheets, maintenance manuals and oil analysis reports.
- Abrasive wear
- Removal of material caused by hard particles, such as dust or metal fragments, that score surfaces in motion. It is countered by keeping the lubricant clean through filtration, effective seals and correct top-up practices.
- Acid number
- The amount of base needed to neutralise the acids present in one gram of oil, expressed in milligrams of potassium hydroxide. An increase during service generally indicates oxidation of the lubricant.
- Additive
- A substance added to the base oil to improve its properties or give it new ones, such as resistance to oxidation or protection against wear and corrosion. All the additives in a product are often called the additive package.
- Adhesive wear
- A form of wear in which the asperities of two surfaces in contact weld locally and tear apart during movement. It occurs when the lubricant film is insufficient and, in the most severe cases, leads to seizure.
- Antifoam agent
- An additive that helps air bubbles on the surface of the oil to break. Foam reduces lubricating ability, impairs cooling and, in hydraulic circuits, makes the operation of actuators irregular.
- Antioxidant
- An additive that slows down chemical reactions between oil and oxygen, which are accelerated by heat and by the presence of metals. It extends the service life of the lubricant and limits the formation of sludge, varnish and acids.
- Anti-wear additive
- An additive that forms a protective layer on metal surfaces, useful when the lubricant film becomes thinner, for example at start-up or under moderate loads. It is found in many hydraulic oils, engine oils and gear oils.
- Base number
- A measure of an oil's alkaline reserve, expressed in milligrams of potassium hydroxide per gram. It is typical of engine oils and shows their ability to neutralise combustion acids; it decreases during service.
- Base oil
- The main component of a lubricant, to which additives are added. It may be of mineral, synthetic or vegetable origin and determines many of the product's characteristics, such as temperature behaviour and stability.
- Biodegradability
- The ability of a substance to be broken down by microorganisms present in the environment. For lubricants it is assessed with standardised tests and is an important requirement, together with low toxicity, for applications at risk of release.
- Boundary lubrication
- A regime in which the lubricant film is so thin that the asperities of the surfaces come into contact. Protection depends mainly on additives. It occurs at start-up, at low speeds and under high loads.
- Cavitation
- The formation and subsequent collapse of vapour or gas bubbles in a liquid, in areas where the pressure drops too low. In hydraulic circuits it damages pumps and components, causing noise and erosion of surfaces.
- Centralised lubrication
- A system that automatically or semi-automatically delivers oil or grease to several points on a machine through a pump, distributors and lines. It ensures regular supply and reduces the risk of missed lubrication points.
- Coefficient of friction
- The ratio between the force needed to make two surfaces slide and the load pressing them together. It is a dimensionless number: the lower it is, the lower the resistance to movement between the two surfaces.
- Consistency
- The degree of softness or hardness of a grease. It is measured with a penetration test using a standard cone and expressed on a scale of grades ranging from 000, almost fluid, to 6, very hard.
- Contamination
- The presence in the lubricant of foreign substances such as dust, metal particles, water, air, fuel or other lubricants. It is one of the main causes of premature wear and failures in lubricated systems.
- Corrosion inhibitor
- An additive that protects metal surfaces from attack by water, oxygen and acidic substances. Rust inhibitors protect ferrous metals, while other additives are specific to copper and yellow metal alloys.
Terms from D to H
- Demulsibility
- The ability of an oil to separate quickly from water instead of forming a stable emulsion. It is important for hydraulic, turbine and gear oils, where water must be able to be drained from the bottom of the reservoir.
- Detergent
- An additive typical of engine oils that counteracts the formation of deposits on hot surfaces and, thanks to its alkaline nature, helps to neutralise the acids produced by combustion, protecting pistons, rings and other internal engine parts.
- Dispersant
- An additive that keeps soot and residues finely suspended in the oil, preventing them from clumping together and settling as sludge. The dirt is then removed with the filter and at each oil change.
- Dropping point
- The temperature at which a grease, in a standard test, becomes fluid enough to drip. It is used to compare products, but it does not indicate the maximum service temperature, which is always lower.
- Dynamic viscosity
- A measure of a fluid's internal resistance to flow, expressed in millipascal seconds. It equals kinematic viscosity multiplied by density and is used above all to describe behaviour at low temperatures.
- Elastohydrodynamic lubrication
- The lubrication regime of highly concentrated contacts, such as those in rolling bearings and gears. The very high pressure elastically deforms the surfaces and increases the oil's viscosity in the contact zone, forming a very thin but effective film.
- Extreme pressure
- The term used for additives that react with metal surfaces when very high loads raise the temperature at the contact points, forming layers that prevent the asperities from welding together. They are typical of gear oils.
- Flash point
- The minimum temperature at which the vapours of an oil ignite in contact with a flame, under defined test conditions. It is an important figure for safety during handling and storage.
- Friction modifier
- An additive that reduces the coefficient of friction in the boundary and mixed regimes. It contributes to energy savings and, in some applications such as wet clutches and brakes, is used to control frictional behaviour.
- Graphite
- A form of carbon with a layered structure whose layers slide easily over one another. It is used as a solid lubricant in greases, pastes and dispersions, and works best in the presence of ambient humidity.
- Grease
- A semi-solid lubricant made of base oil, thickener and additives. It stays where it is applied, protects against the ingress of contaminants and is used mainly for bearings, joints and mechanisms without oil circulation.
- Hydraulic oil
- A fluid used in hydraulic circuits to transmit power, lubricate pumps and motors and remove heat. It must have suitable viscosity, anti-wear properties, good air and water separation and resistance to oxidation.
- Hydrodynamic lubrication
- A lubrication regime in which the relative motion of the surfaces drags the lubricant into a converging gap, generating a pressure that separates them completely. It is typical of plain bearings in steady operation.
Terms from K to P
- Kinematic viscosity
- A measure of a fluid's resistance to flow under its own weight, expressed in square millimetres per second. For oils it is normally measured at 40 °C and 100 °C and forms the basis of viscosity classifications.
- Lubricant film
- The layer of lubricant between two surfaces in motion. Its thickness, compared with the roughness of the surfaces, determines whether contact takes place in the boundary, mixed or full-film regime.
- Metallic soap
- A grease thickener obtained by reacting fatty acids with compounds of metals such as lithium, calcium, sodium or aluminium. The type of soap influences water resistance, operating temperature and the stability of the grease.
- Mineral oil
- A base oil obtained by refining crude oil. It is the most widespread type because of its good balance between performance and cost; more advanced refining processes improve its purity and stability.
- Molybdenum disulphide
- A dark grey solid lubricant with a lamellar structure. Added to greases and pastes, it improves protection in slow movements and under high loads, and is particularly effective in dry environments.
- Oil analysis
- A laboratory examination of a sample of in-service lubricant. It assesses the condition of the oil, the presence of contaminants such as water and dust, and the metal particles caused by wear, helping to plan maintenance based on actual condition.
- Oil separation
- The phenomenon in which part of the base oil separates from the thickener of a grease. Moderate separation is normal and necessary for lubrication; excessive separation, even during storage, indicates instability of the product.
- Oxidation
- A chemical reaction between the lubricant and oxygen, accelerated by heat, water and metals. It leads to an increase in viscosity and acidity and to the formation of deposits: it is the main cause of oil ageing.
- Polyalphaolefin
- A hydrocarbon-type synthetic base oil. It has a high viscosity index, excellent flow at low temperatures and good oxidation stability, and is compatible with many of the materials used with mineral oils.
- Polyglycol
- A synthetic base oil with good lubricating properties and a high viscosity index, used for example in some gearboxes and compressors. It is generally not miscible with mineral oils: changing product requires particular care.
- Pour point
- The lowest temperature at which an oil can still flow under standard test conditions. It is useful for assessing whether a lubricant is suitable for use in cold environments and for machines that must start outdoors in winter.
- PTFE
- Polytetrafluoroethylene, a polymer with a very low coefficient of friction and good chemical inertness. It is used as a solid lubricant in powders, dispersions, greases and anti-friction coatings, especially where low friction and a surface that does not easily hold dirt are wanted.
Terms from R to V
- Relubrication
- The periodic addition of fresh grease to a bearing or joint to restore lubrication and remove degraded or contaminated grease. Quantity and frequency depend on the component, speed, temperature and environment.
- Seizure
- Severe damage that occurs when two metal surfaces come into direct contact and weld locally, to the point of stopping movement. It is the extreme consequence of adhesive wear and can be caused by lack of lubricant, insufficient viscosity or overheating.
- Stick-slip
- The jerky movement of a surface sliding slowly over another, caused by the difference between static and kinetic friction. It is typical of machine tool slideways and is countered with specially formulated slideway oils.
- Synthetic ester
- A base oil obtained by reacting acids with alcohols. It offers good thermal stability, good lubricating properties and, in many formulations, high biodegradability. Some esters can be sensitive to the presence of water.
- Synthetic oil
- A base oil produced by chemical synthesis, with molecules designed for specific performance. It generally offers better stability at high temperatures, better flow in the cold and a longer service life than a mineral oil.
- Thickener
- The component that gives a grease its semi-solid consistency. It forms a structure that holds the base oil and releases it gradually during operation. It may be based on metallic soaps, complex soaps or non-soap substances such as polyurea and clays.
- Tribology
- The science that studies friction, wear and lubrication of surfaces in relative motion. It combines knowledge of mechanics, chemistry and materials science and provides the basis for designing longer-lasting components and choosing the most suitable lubricants.
- Viscosity index
- A number that describes how much the viscosity of an oil changes as temperature changes. A high index indicates more stable behaviour between cold start-up and hot operation, which is useful for machines working across wide temperature ranges.