Friction reduction: how industrial lubricants work

Reducing friction means using less energy, generating less heat and causing less wear: the principles of tribology applied to the selection and everyday use of lubricants.

  • Lubrication regimesboundary, mixed, full film
  • Wearadhesive, abrasive, fatigue
  • Solid lubricantsgraphite, molybdenum disulphide, PTFE

Friction: a hidden cost in every machine

Friction is the resistance that opposes relative motion between two surfaces in contact. In every machine part of the energy is spent overcoming it and is turned into heat; at the same time, friction goes hand in hand with component wear. Reducing it in a controlled way is the main task of industrial lubricants.

The discipline that studies friction, wear and lubrication is called tribology. It is not a subject reserved for laboratories: its principles explain why a bearing overheats, why a gear is damaged after starting under load, or why a machine tool slideway moves in jerks. Understanding them helps to choose lubricants better and to interpret the signals that machines give.

Why surfaces wear

Even surfaces that look perfectly smooth show peaks and valleys, called asperities, when seen under a microscope. When two surfaces rest on each other, contact only occurs at the tips of these asperities, where local pressures are extremely high. If the surfaces move without a lubricant, the asperities deform, weld locally and tear apart, generating heat, particles and progressive damage.

Friction is measured with the coefficient of friction, which is the ratio between the force needed to make the surfaces slide and the load pressing them together. In general, the friction needed to start movement, known as static friction, is greater than the friction opposing movement once it has started, known as kinetic friction. This difference is the origin of jerky motion, known as stick-slip, typical of slideways moving slowly: this is why there are slideway oils formulated specifically to reduce it.

Industrial lubricating oil poured onto the teeth of a gear to reduce friction and wear
In gears the lubricant film is extremely thin and works at extremely high pressures.

Lubrication regimes

The behaviour of a lubricant depends on how well it separates the surfaces. Four regimes are distinguished.

  • Boundary lubrication The film is so thin that the asperities come into contact. Protection relies mainly on additives, which form protective layers on the surfaces. It is typical of start-ups, low speeds and very high loads.
  • Mixed lubrication The load is carried partly by the fluid film and partly by contact between asperities.
  • Hydrodynamic lubrication Relative motion drags the lubricant into a narrowing gap, generating a pressure that separates the surfaces completely. This is the case of plain bearings in steady operation.
  • Elastohydrodynamic lubrication In highly concentrated contacts, such as those of rolling bearings and gears, the pressure is so high that it elastically deforms the surfaces and greatly increases the oil's viscosity in the contact zone: a very thin but effective film is formed.

The transition between these regimes is described by the Stribeck curve, which relates the coefficient of friction to a combination of viscosity, speed and load. At low speed or with insufficient viscosity, friction is high because contact between asperities dominates; as speed or viscosity increases, friction falls to a minimum; beyond this point it rises slowly again because of the fluid's internal resistance.

Practical consequences for choosing viscosity

The Stribeck curve explains why viscosity must be chosen with balance. An oil that is too thin cannot form a sufficient film and pushes the contact towards the boundary regime, with greater wear. An oil that is too viscous separates the surfaces well, but increases losses due to internal friction in the fluid, runs hotter and circulates with more difficulty, especially at cold start. That is why manufacturers specify precise viscosity grades, calculated on the basis of speeds, loads and operating temperatures.

Wear mechanisms

  • Adhesive wear Surfaces weld locally and tear apart; in severe cases it leads to seizure.
  • Abrasive wear Hard particles, such as dust or metal debris, score the surfaces: filtration and cleanliness are the first line of defence.
  • Surface fatigue Repeated loads in rolling contacts generate micro-cracks that lead to fragments of material breaking away.
  • Corrosive wear Water and aggressive substances attack the surfaces, and the corrosion products are removed by the motion.
  • Fretting Very small oscillating movements, typical of fits subject to vibration, damage surfaces even without visible sliding.

Additives that reduce friction and wear

When the fluid film is not enough, additives come into play. Anti-wear additives form protective layers on the surfaces that reduce metal-to-metal contact under moderate loads. Extreme pressure additives react with the surfaces when the local temperature rises under very high loads, creating layers that prevent the asperities from welding: they are essential in heavily loaded gears. Finally, friction modifiers reduce the coefficient of friction in the boundary and mixed regimes, also contributing to energy savings.

Solid lubricants and coatings

In some applications an oil or grease cannot be used or is not enough: very high temperatures, very slow movements under high loads, dusty environments where an oily film would hold dirt. In these cases solid lubricants are used.

  • Graphite It has a layered structure whose layers slide easily; it works well in the presence of ambient humidity.
  • Molybdenum disulphide Also lamellar, effective under high loads and in dry environments.
  • PTFE A polymer with a very low coefficient of friction, used as a powder, in dispersions or in coatings.

These materials are found in assembly pastes, greases with solid additives, dispersions and anti-friction dry film coatings, which are applied to surfaces and bonded to them firmly.

Good practice for reducing friction

  • respect the viscosity grade and specifications given by the manufacturer;
  • keep the lubricant clean with filtration and correct top-ups;
  • avoid both too little and too much lubricant;
  • take care of alignment, assembly and surface finish;
  • monitor temperatures and vibration, early signs of lubrication problems.

Sprays and aerosol products

Many anti-friction lubricants are available in aerosol cans: the propellants are often flammable, so they must be used in ventilated areas, away from flames, sparks and hot surfaces, and always with the machine stopped.